New Products

Coming Soon: CCL & CCR

CCL80 Series Actuator Preliminary Specs:

  • DIMENSION: Ø80X195
  • LINEAR STROKE: 10, 25 mm (other strokes are available up to 200mm upon request.)
  • ENC. RESOLUTION: 5, 1 µm
  • PEAK FORCE: 140N @ 48 Vdc
  • FORCE CONSTANT: 36 N/A
  • MOVING MASS: 0.42 kg
  • TOTAL MASS: 4.65 kg
  • IP65/IP67 Standard options
  • IP69 per special request

 

 

SMAC CCL 

 

SMAC Introduces Programmable Micro Gripper
for Handling Fragile Parts

SMAC Moving Coil Actuators introduced details for their new MGR5 Series Micro Gripper. The SMAC MGR5 Series Micro Gripper is very light - around 30 grams - and can be used as an end effector on third party robots. The unit sells for less than $1,000, providing a reasonable cost for the solution.

The MGR5 Series Micro Gripper was developed to handle small very fragile parts - in SMAC’s case - the assembly of small and precise rotary encoders. It includes the company’s patented Soft-Land feature, programmable force down to 5 grams, and two independently controlled gripper fingers to pick up asymmetric parts.

The MGR5 enables increased small part assembly - particularly of complicated small products that are made in very high quantities. Small part assembly is increasing - due to consumer product trends - such as smart phones and watches. These parts are too small and fragile to be handled by most humans. The product also feeds back what happened during the process - i.e. pick up occurred - correct position achieved - part was put down - etc.

MGR5 Series Micro Gripper Specs:

  • Dimensions [mm]:       30x47x19.5
  • Stroke [mm]:   10 (5 each)
  • Peak Force [N]:          1.7 @ 1.5 Amp (24VDC)
  • Encoder Resolution [µm]:       5 standard, 1.0 optional

The stroke of the MGR5 Series Micro Gripper is 10 mm (i.e., 5 mm per axis).

Small grippers are primarily pneumatic. Guides are not good, forces are too high due to seal friction, and gripper is single axis so off-set parts can be damaged.

SMAC’s built-in sensor feedback system gives SMAC’s devices, including the Micro Gripper, the unique mechatronic ability to “perform a task and verify its quality at the same time.” This would allow the actuators to quality check key processes 100% in real time and feedback the results.

SMAC Moving Coil Actuators is primarily known for its true “mechatronic solutions.” By that they mean their  actuators have unique capabilities such as programmable and controllable position, velocity, and force, high accelerations, cycle life well over 100M, and a patent-pending “Soft-Land” capability. The Soft-Land capability is very useful when performing fragile part assembly, measurement, moving objects, etc.

SMAC electric grippers incorporate programmable speeds, positions and forces with data feedback. The ability to independently control each jaw allows precise force control, measurement and positioning. This makes them ideal for a wide range of positioning, measuring, and inspection applications, particularly where 100% verification is required.

 

 

SMAC Micro Gripper 


 

Introducing the Thinnest Moving Coil Linear Motor in the World, the LCA6

SMAC Moving Coil Actuators introduces the LCA6. At 6mm wide, SMAC Moving Coil Actuators claims that the LCA6 is the thinnest linear moving coil in the world. The LCA6 is cross roller guided, increasing accuracy. Flat coils are centred between cross rollers so deflection load is reduced and rigidity is increased. In addition, the LCA6 is small and stackable, conserving space.

LCA6 Specs:

  • Dimensions [mm]: 60x135x6
  • Linear Stroke [mm]: 10
  • Encoder resolution [µm]: 5 standard, 0.1 opitonal
  • Moving mass [kg]: 0.037
  • Total mass [kg]: 0.21 (w/o cable)
  • ​Peak Force [N]: 3.5 @ 1.2 amps (24V)
  • Vacuum and spring optional

The LCA6 is great for electronic pick-and-place, biomedical dispensing, and QC measurement. 

The LCA6 benefits include a compact and slim package, superior cross ruler guiding, ultra-low friction, ultra-smooth and rigid guiding, programmable position, force, velocity, Soft-Land capability, and feedback of position, force, and velocity.

SMAC’s built in sensor feedback system gives SMAC’s Moving Coil Actuators the unique mechatronic ability to “do work and verify its success at the same time.” This would allow the actuators to quality check key processes 100% in real time and feedback the results.

SMAC Moving Coil Actuators claim to be true “mechatronic solutions.” By that they mean their  actuators have unique capabilities such as programmable and controllable position, velocity, and force, high accelerations, cycle life well over 100M, and a patent-pending “Soft-Land” capability. The Soft-Land capability is very useful when performing fragile part assembly, measurement, moving objects, etc.

SMAC’s low friction guide system makes their actuators extremely repeatable from move to move - within 1 msec. SMAC’s product development group originated such models as the Linear/Rotary actuator, the 2 independent axis Gripper, the world’s first direct drive Robotic Finger, and advanced magnetic circuit designs that have more than doubled forces in the same sized mechanical packages.

LCA6 
 

 

SMAC Direct Drive Servo Motor Robotic Finger

At the Automate 2015 show in Chicago, SMAC Moving Coil Actuators introduced a prototype version of the world's first direct drive servo motor robotic finger, acknowledged as a technological breakthrough by a leading European technical university. It is shown here operating a Samsung Galaxy touchscreen phone. SMAC expects an early 2016 release to be shortly followed by a robotic thumb and ultimately the first true functional robotic hand capable of reproducing work done by human hands.

The first motor is a 25 mm-diameter servo "partial" motor and is equipped with an SMAC rotary encoder with 15.5K counts per revolution. It achieves a high torque/diameter ratio due to the proprietary magnetic circuit design as well as the coil design. Intellectual property rights have been addressed. This motor acts as the PIP joint.

Another larger motor, 35 mm diameter, acts as the 2nd joint (MCP FLex). It puts out a torque of 630 mNm and thus can exert a resultant force of 7N at the tip. Both motors move 45 degrees as the human joints do.

The 3rd motor operates as a third joint (MCP ab/ad). This is the joint that moves side to side. This motion is based on SMAC’s moving coil linear design and already meets the required parameters.

These motors have been integrated into a structure that allows them to operate and cover the same movement capability as a human’s finger. The structure weighs approximately 350 grams and is physically about 1.5 x larger than the average male finger.

Watch the presentation given at Hannover Messe 2015.

See the world's first direct drive servo motor robotic finger live.

 

 

 

CBL35C Series Electric Cylinder with Built-in Controller

Introducing the 35mm diameter CBL35C electric cylinder with built-in controller. The new CBL35C series electric cylinder with built-in controller in a single package enables the direct replacement of existing pneumatic cylinders and retro-fits without any machine modifications required. With our built-in controller, the CBL35C can control the force, speed and velocity profile. The CBL35C with built-in controller allows simple installation and effective use of space.  

The CBL35C provides significantly longer life, programmability, high speed, accuracy and energy efficiency while remaining price-competitive. The CBL35C also provides more sustainable solution by not requiring costly compressed air.

Our Graphical User Interface is also available for the built-in controller for easy, straightforward setup of parameters. It allows you to change product profiles on the fly and improves factory uptime.

  • Dimensions [mm]: Ø35 x 135 - 217(depending on stroke)
  • Stroke [mm]: 10, 25 (+1/-0)
  • Acceleration[G]: up to 50 (zero payload)
  • Peak Force [N]: up to 61
  • Encoder Resolution [µm]: 5 (standard) 1 & 0.1 (Options)
  • SMAC’s Patented: ‘Soft-Land’ Technology

 


 

LCR13 Series Linear Rotary Actuator

Introducing a new range of electric linear rotary actuator with only 13mm in width. The LCR13 is compact direct-drive brushless servo motor. The precision Z-theta motion within one small actuator, providing a convenient pick, orient and place. The LCR13 has a light moving mass of 95 grams, which results in high accelerations. The vacuum-built-in shaft through the rotary motor is available to prevent dust build-up in the unit. The LCR13 can easily be programmed to control force/torque, position and velocity in all axes at the same time with feedback capability. Patented SMAC's unique "Soft-Land" function enables the unit to gently land on a delicate component with a controlled force to avoid damage of both the component and the pick and place head.

 

  • Dimensions [mm]: 75 x 155 x 13
  • Stroke [mm]: 25 (+1/-0)
  • Peak Force [N]: 7 @ 3A
  • Linear Encoder Resolution [µm]: 5 standard, 1 optional
  • Peak Torque [Nm]: 0.047 (24VDC)
  • Rotary Encoder Resolution: 24K/Rev
  • Combined linear and rotary motions in a single unit
  • Fully programmable in force/torque, position and velocity
  • SMAC’s Patented ‘Soft-Land’ Technology
  • Low shaft run-out, 30µm (Lower run-out optional)
  • Self-lubricated linear guide
  • Vacuum through shaft prevents dust accumulation
  • Spring option

 
 


 

CBL35 Series Electric Cylinder

Introducing a new range of Electric Cylinder designed to overcome problems with existing conventional devices in the packaging industry with improved cycle ate, uptime, work environment, etc. For end users and machine manufacturers.

The CBL35 offers cycle life well beyond 100million cycles. It achieves accelerations up to 50G, enabling the actuators to cycle at rate >2000CPM.

Fully programmable in force, position and velocity, it can be adjusted in seconds and does not require recalibration. Precise motion control has inherent force feedback capabilities. This results in a huge saving of time and cost, and increases throughput due to a significant reduction in machine down time. Cleaner and quieter operation with no exhaust air.

 

  • Dimensions [mm]: Ø35 x 95 (10mm stroke, single coil)
  • Stroke [mm]: 10, 15, 25 (+1/-0)
  • Acceleration[G]: up to 50 (zero payload)
  • Peak Force [N]: 8.5 - 18
  • Encoder Resolution [µm]: 5 standard, 1 optional
  • SMAC’s Patented: ‘Soft-Land’ Technology
 
 

 


 
©2017 SMAC Corporation | 5807 Van Allen Way | Carlsbad, California 92008
Tel: 760-929-7575 | Fax 760-929-7588

Site Credits: Ecreativeworks