|
|
Upcoming SMAC Shows and Events
EASTPACK 2012
MAY 22-24
Philadelphia, PA
Booth #2856
PACKEXPO 2012
OCT 28 - 31
Chicago, IL
Booth #4574
|
|
|
Servo cables for SMAC Electric Actuators
Cables
|
Single Axis Controller |
Dual Axis Controller |
Amplifier |
Smart Driver |
|
Actuator |
LAC-1 |
LCC-10(11) |
LAC-25 |
LAA-5 |
LAD-1 |
|
CAL |
CAH-LOD26-03 |
CAH-LOD26-03 |
|
CAH-LAD26-03 |
CAH-LSD26-03 |
No cable required for flying lead option |
2x CAL |
|
|
CAH-LTD-03 |
|
|
No cable required for flying lead option |
|
|
|
|
|
|
|
LCA(S) single/double coil |
CAH-LOD26-03 |
CAH-LOD26-03 |
|
CAH-LAD26-03 |
CAH-LSD26-03 |
No cable required for flying lead option |
LCA(S) 6 coil |
|
MAH-LOD26-03 |
|
|
|
No cable required for flying lead option |
|
|
|
|
|
|
|
LAL35/LAL95 |
LAH-LOD26-03 |
LAH-LOD26-03 |
|
LAH-LAD26-03 |
LAH-LSD26-03 |
|
LAL55/LAL300/LAL500 |
LAH-LOD-03 |
LAH-LOD-03 |
|
LAH-LAD-03 |
LAH-LSD-03 |
|
|
|
|
|
|
|
|
LAR15** |
|
|
LAH-RTD26-03** |
LAH-RAD26-03 |
LAH-RSD26-03 |
Also need PT30-26** |
LAR20/LAR35 |
|
|
LAH-RTD26-03 |
LAH-RAD26-03 |
LAH-RSD26-03 |
|
LAR55 / LAR95 /LAR300 / LAR500 |
|
|
LAH-RTD-03 |
LAH-RAD-03 |
LAH-RSD-03 |
|
|
|
|
|
|
|
|
2 x LAL35 /LAL95 |
|
|
LAH-LTD26-03 |
|
|
|
2 x LAL55/LAL300/ LAL500 |
|
|
LAH-LTD-03 |
|
|
|
|
|
|
|
|
|
|
LXY15 |
|
|
LAH-GRP-03 |
|
|
|
LXY25 |
|
|
LAH-GRP-03 |
|
|
|
GRP20 |
|
|
LAH-RTD26-03 |
|
|
|
GRP35 |
|
|
LAH-RTD26-03 |
|
|
|
GRP50 |
|
|
LAH-RTD26-03 |
|
|
|
GRP30 (obsolete)
- Requires LAH-PT30-25 (Jumper to 25 pin cable) or LAH-PT30-26 (Jumper to 26 pin cable) as supplement.
- Old type of GRP50 requires LAH-GRP26-03 cable.
- Requires CAH-PT14-26 (1Ft / 0.3m) as supplement for flying lead type.
Why Use Them?
SMAC actuators are used in numerous high speed, high cycle applications and are guaranteed for millions of cycles. For this reason, it is imperative that the cables used to connect with our actuators are capable of similar arduous duty cycles and life span. Only cables manufactured by SMAC can be guaranteed to meet the rigorous standards required during use. Many years of experience has taught us that cheaper third party cables simply are not up to the task required. They are, in fact, one the most common causes of all the technical problems experienced by our customers.
The first question we always ask when a customer calls our technical support office is "Are you using cables supplied and manufactured by SMAC?" If the answer is no, then 99% of the time, we have found the fault, right off the bat.
For this important reason, SMAC produces in-house a range of high quality pre-tested cables for use with all actuator/controller combinations. All SMAC cables have motor and encoder signals separate from each other and shielded accordingly. All cables manufactured by SMAC are 100% tested prior to shipping.
Standard cable lengths are three meters; however, cables are available in longer lengths if required. For applications where the actuator is being moved on another axis, SMAC recommends the use of our "Superflex" cables which are available from SMAC as an option across the range.
For customers who do insist on supplying or manufacturing their own cables, it should be noted and clearly understood that the SMAC product warranty is invalid unless the cable has been fully checked and authorized by an SMAC engineer prior to connection.
Why take the risk? Why have the hassle? By fitting SMAC manufactured cables, you can rest assured they are of the right technical specification, fully tested and up to the job at hand.
|
Privacy
Terms and Conditions
©2012 SMAC Inc.